Rx Frsky

Receiver Adapter Support PWM Signal Output for TBS Crossfire Nano RX FrSky R9 Slim Slim+ Receiver Specification: Item name: Receiver Adapter Usage: With this board you can enable connectivities with your servos via 6ch PWM (with FrSky R9 Slim/ Slim+); 4ch PWM (with TBS Crossfire Nano RX) Compatibility: TBS Crossfire Nano RX and FrSky R9 Slim/Slim+ receivers Output: 6ch PWM for FrSky receivers or 4ch PWM and BST for TBS receivers Size: 25 x 19 x10mm (With Pins) Cable length: 100mm Weight: 2.5g Features: Hassle free and easy soldering Convert PWM signal for servos Note: Receiver not included. Package Included: 1 x RX Adapter 1 x RX Adapter Cable for Crossfire Nano RX 1 x RX Adapter Cable for FrSky Slim/Slim+ RX

9 PCS FuriousFPV JST-GH 1.25mm JST-SH 1.0mm Molex 2P 3P 4P Silicone Wires for RX VTX Camera GPS bluetooth Buzzer Frsky RX Airspeed F-35 Lightning Wire Harness: Silicone wire (AWG 28) 9 Harness/set Package Included: (length and connector) Camera: 220mm - JST GH 4pins 1.25 to MOLEX 3pins 1.25 + MOLEX 2 pins 1.25 VTX: 400mm - JST GH 4pins 1.25 to JST GH 6pins 1.25 RX Frsky: 400mm - JST GH 4pins 1.25 to Molex 1.25 5pin TBS Micro Rx: 400mm - JST GH 4pins 1.25 to MOLEX 6pins 1.25 GPS: 200mm - JST GH 4pins 1.25 to MOLEX 4pins 1.25 bluetooth: 100mm - JST GH 4pins 1.25 to JST SH 4pins 1.0 Air Speed : 200mm - JST GH 4pins 1.25 to MOLEX 4pins 1.25 Buzzer: 100mm - JST GH 2pins 1.25 to wire External wires for TBS Micro RX: 400mm - JST GH 4pins 1.25 to Molex Pins 1,25

2.4G 4CH Mini Receiver Compitable Frsky X9D PLUS XJT DJT DFT DHT Description: Item Name: RX-4CH Receiver Channel: 4CH Weight: 5g Signal: PPM Output Compatible with Frsky X9D remote controller (D8 mode) XJT(D8 mode) DFT, DJT, DHT Features: -PPM Output (4CH receiver still outputs the full 8-channel ppm) -Connect 1-3 signal, 4-channel will convert to PPM output, can be used to connecting flight control, wireless simulation or or Wi-coach. -Fail-safe protection, only support third channel protection. Pacakge Included: 1X RX-4CH Receiver

DIY RX-F802 8CH Receiver for FRSKY X9D(PLUS) DJI DFT DHT Specification: Channel: 8 Working voltage: 4-6.5V Frequency range: 2400-2483.5Mhz Output signal: PWM/PPM Dual way transmission: Yes(D8 mode) Transmit distance: > 1Km Feedback signal: RSSI, 3S voltage (A1) Dimension: 4.1*2.4*0.8cm (includes pin) Antenna length: 15cm With Failsafe Suitable for fixed-wing, glider Compatible with X9D(D8 mode)/XJT (D8 mode)/DJI/DFT/DHT Package included: 1 x RX-F802 receiver

1g Super Mini AC900 Dual Mode Receiver Compatible Frsky D16 & Futaba S-FHSS RX Built-in LNA Chip Specification: Item Name: Super Mini AC900 Dual Receiver Model: AC900 Working Voltage: 4-6V Dimension: 10.3x16.6mm Weight: 0.9g - Support Futaba S-FHSS and Frsky D16 ( No Telemetry ) dual receiver mode. - S-FHSS mode support 14SG, 16SG, 18SZ, 18MZ etc. - D16 Mode support X9D, X12S etc. - with high-performance discrete LNA chip. - Receiver working range is 200m, air distance about 500m. Package Included: 1x AC900 Receiver 1x Manual

8CH SUBS Super Micro Receiver for Frsky X9D Plus Description: Item name: Micro Compatible Receiver for Frsky Size: 10X12MM Weight: 0.45 grams Working voltage: 3.3v-5v Operating current: 20MA (5V) Working distance: 200M Output channel: Up to 8ch from sbus Factory settings is the latest 0.21 OpenSky firmware. Features: * 16x16mm hole to hole spacing (20x20mm outer dimension) * Integrated FrSky compatible SBUS receiver (basically an integrated uSKY rx) * STM32F3 CPU * MPU-6000 SPI gyro * Supports DSHOT * Integrated Blackbox dataflash * Integrated voltage- and current-sensor * Buzzer output * rgb led output * Open hardware * (optional) add on PCB for quad brushed support Package Included: 1X 8CH SUBS Super Micro Receiver

FrSky Taranis X9 Lite 2.4GHz 24CH ACCESS ACCST D16 Mode2 Classic Form Factor Portable Transmitter for RC Drone Frsky will provide an upgrade program in the future, you can choose Access or Accst D16. Specifications: Brand name: FrSky Item name: Taranis X9 Lite Transmitter Version: Non-EU Version Dimension: 184*170*101mm (L*W*H) Weight: 505g (without battery) Operating system: ErskyTX / OpenTX (Default: OpenTX) Number of channels: 24 channels Internal RF module: ISRM-N Operating voltage range: 6.0~8.4V Operating current: [email protected] Operating Temperature: -20 ~ 60 (-4 ~ 140) Backlit LCD resolution: 128*64 Model memories: 60 models (expandable by Micro SD card) Smart Port, Micro SD card slot, Micro USB Port and DSC Port Details of FrSky ACCESS main functions and features, Please click here. Details of FrSky ACCST D16 main functions and features,Please click here. Recommended receiver(ACCESS Rx): FrSky R-XSR click FrSky RX6R click FrSky RX4R click FrSky G-RX6 click FrSky G-RX8 click Recommended Battery: 18650 Li-ion Battery Click Here Features: Ergonomic and compact design Installed with ACCESS protocol Supports spectrum analyzer function High-speed module digital interface G7 Noble potentiometer gimbal Supports wired training function Haptic vibration alerts and voice speech outputs Easily accessible battery compartment (*Batteries not included, adaptive with replaceable 18650 button top Li-ion batteries) As a portable radio, the FrSky Taranis X9 Lite is a remarkable fusion of

SPC Maker Killer Whale 115mm F4 FPV Racer w/ 1103 8500KV Runcam Nano 2 Camera Specification: Brand Name: Spc Maker Model: Killer Whale Item Name: 115mm Whoop FPV Racing Drone Version: PNP ( Without Receiver) / Compatible Flysky RX/ Compatible Frsky RX Compatible DSM2/DSMX RX / Compatible Futaba Receiver ( Optional) Canopy Color: Black / Bule ( Optional) Wheelbase: 115mm Weight: 51g ( Without Battery) Flight Controller: MICRO F4 Flight Controller Firmware: OMNIBUS F4SD ESC: MICRO 12A 2-3S Blheli_S 4 In 1 ESC Motor: 1103 8500KV Brushless Motor Propeller: Kingkong 65mm 2-Blade Propeller w/ 1.5mm Hole FPV Transmitter: 5.8G 40CH 25/100MW VTX Receiver: Without Receiver/ Compatible Flysky RX/ Compatible Frsky RX Compatible DSM2/DSMX RX / Compatible Futaba Receiver ( Optional) FPV Camera: Runcam Nano 2 700TVL Camera Battery: NOT Include Package Included: 1 xKiller Whale Kit 4 x 1103 8500KV Motor 1 x MICRO F4 Flight control 1 x MICRO 12A 4IN1 ESC 4 x Kingkong 65mm 2-Blade Propeller CW 4 x Kingkong 65mm 2-Blade Propeller CCW 1 x Runcam Nano 2 Camera 1 x 5.8G 40CH VTX 2 x Rubber Band 1 x Compatible DSMX/Frsky/Flysky/futaba Receiver (optional)

Finally a solution from FrSky for all those micro brushed quads. F3EVO running betaflight and fully firmware upgradeable. Pre-soldered connectors makes this unit ready to install and bind. Upgrading your Tiny Whoop has never been easier.Specifications: Dimension: 29��29��6mm (L �� W �� H) Hardware: STM32F303 CPU (72MHz inc FPU), MPU9250 (accelerometer/gyro/compass), CC2510 CPU for XM receiver Weight: 3.4g Channels: 16CH (8CH is RSSI) by SBUS to UART2 Rx of F3EVO Operating voltage/current: 4.2V@75mA Compatibility: FrSky Taranis X9D/X9E/Q X7/ Horus X12S/XJT in D16 mode Firmware Upgradeable

Specification: Brand name: Eachine (Frsky version) CRAZYBEE F4FR PRO V3.0 Firmware target: CrazybeeF4FR (Flysky version) CRAZYBEE F4FS PRO V3.0 Firmware target: CrazybeeF4FS (No RX version) CRAZYBEE F4 PRO V3.0 Firmware target: CrazybeeF4DX MCU:STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU-6000(SPI connection) Board size: 28.5 * 28.5MM Power supply: 2-4S battery input (DC 7-17V) Built-in 10A(each) Blheli_S 4in1 ESC Dshot600 ready Frsky version Built-in SPI Frsky receiver with telemetry(D8/D16 switchable) Flysky version Built-in SPI Flysky receiver with telemetry(AFHDS/AFHDS2A switchable) No RX version need to add external Receiver Built-in Betaflight OSD(SPI Control) Built-in Current meter Max 70A Current meter scale set to 470 Built-in 5V 1A BEC Built-in voltage detection MCU upgraded to EFM8BB21 Power supply: 2-4S LiPo/LiPo HV (7v/17v) Current: 10A continuous peak 12A (5 seconds) Support BLHeliSuite programmable Factory firmware: F_H_40_REV16_5.HEX Default protocol: DSHOT600 SPI BUS receiver Frsky D8/D16 switchable Compatible Non EU transmitter both D8 and D16 mode Channels: 8ch or 16ch Failsafe support No ground interference ( Transmitter and receiver 1 m from the ground): 300m SPI BUS receiver Protocol: AFHDS and AFHDS-2A Switchable Channels: 8ch(AFHDS) or 14ch(AFHDS-2A) No ground interference ( Transmitter and receiver 1 m from the ground): 300m Failsafe support No RX version support external serial-bus receiver like XM+ crossfire, S-FHSS etc. Package Included: 1 x CRAZ

Happymodel Mobula6 65mm Crazybee F4 Lite 1S Brushless Whoop FPV Racing Drone BNF Specification: Brand Name: Happymodel Model: Mobula6 Item Name: 65mm Crazybee F4 Lite 1S Brushless Whoop FPV Racing Drone BNF Optional Version: Frsky Receiver ( Compatible with ACCST D8/D16, Recommend D8 mode) Flysky Receiver ( Compatible with AFHDS and AFHDS-2A Flysky transmitter) Drone Wheelbase: 65mm Size: 80x80x37mm Weight: 20g Crazybee F4 LiteFlight Controller Built-in ESC & Receiver & VTX Frsky SPI RX version) CRAZYBEE F4 Lite Frsky version Firmware target: CrazybeeF4FR (Flysky SPI RX version) CRAZYBEE F4 Lite Flysky version Firmware target: CrazybeeF4FS MCU:STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU-6000(SPI connection) Board size: 28.5 * 28.5MM Power supply: 1S battery input (DC 2.9V-4.35V) Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready Built-in Betaflight OSD(SPI Control) Built-in 5.8G VTX Built-in SPI Frsky/Flysky receiver Built-in 5V 1A BEC Built-in voltage detection Onboard Frsky Receiver Version SPI BUS receiver Frsky D8 compatible Compatible Non EU transmitter D8 model - Frsky_x_lbt Support EU LBT Radio Transmitter Channels: 8ch Failsafe support No ground interference ( Transmitter and receiver 1 m from the ground): 100m~200m Onboard Flysky Receiver Version SPI BUS receiver Protocol: AFHDS and AFHDS-2A Switchable Channels: 8ch(AFHDS) or 14ch(AFHDS-2A) No ground interference ( Transmitter and receiver 1 m from the ground): 100~200m Failsafe support Onboard 5A BLheli_S 4in1 ES

MOTIVE-RC R8SB 2.4G 9CH Frsky D8 Compatible Telemetry Receiver for X9D Plus DJT XJT Transmitter Specification: User Manual, DOWNLOAD Brand name: MOTIVE-RC Item name: R8SB 9CH D8 Compatible Telemetry Receiver Number of Channels: Up to 9CH from SBUS(CH1~8 for PWM, CH9 RSSI for FC) Input Voltage Range: 3.5V - 13.0V (5V Normal Operating Range) Range: above 1.2KM Compatibility: iRange X Jumper Transmitters, FrSky XJT / DJT / DFT/ DHT, D8_Mode on all FrSky transmitters Size: 35 x 21 x 12 mm (L x W x H) Weight: 6.8g Feature: 1.2KM far reaching range Satisfy with various model type with Physical channel PWM outputs, PPM, SBUS and RSSI outputs (For FC) RSSI Output analog 0~3.3V Two analog telemetry ports (A1&A2) A1 for internal receiver battery voltage sensor, A2 for external battery voltage sensor (0~30V, 1~6S) One digital data-stream port (Rx, Tx) Package Included: 1 x Telemetry Receiver

Crazybee F4 Pro V2.0 Mobula7 HD 1-3S Flight Controller w/ 5A ESC & Compatible Flysky/Frsky/DSMX Receiver Diffrence from V1.0: - V2.0 could handle 1-3S Lipo/LiHV ( V1.0 only 1-2s Lipo/LiHV) - V2.0 use bigger bind and boot button change the BAT/GND pad to "through hole" Specification: Brand Name: Happymodel Item Name: Crazybee F4 Pro V2 Flight Controller MCU: STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU-6000(SPI connection) Board size: 28.5 * 28.5MM Power supply: 1-3S battery input (DC 3.5-13V) Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready Built-in Receiver ( Diffirent version having diffirent receiver, without receiver version doesn't have rx) Built-in Betaflight OSD(SPI Control) Built-in Current meter Max 28A Current meter scale set to 1175 Built-in 5V 1A Buck / Boost with LC filter Built-in voltage detection Firmware (Frsky version) CRAZYBEE F4FR PRO V2.0 Firmware target: CrazybeeF4FR (Flysky version) CRAZYBEE F4FS PRO V2.0 Firmware target: CrazybeeF4FS (DSM2/DSMX version) CRAZYBEE F4DX PRO V2.0 Firmware target: CrazybeeF4DX (No RX version) CRAZYBEE F4 PRO V2.0 Firmware target: CrazybeeF4DX Onboard 5A 4 In 1 ESC MCU upgraded to EFM8BB21 Power supply: 1-3S LiPo/LiPo HV (3.5v/13v) Current: 5A continuous peak 6A (5 seconds) Support BLHeliSuite programmable Factory firmware: S_H_50_REV16_7.Hex Default protocol: DSHOT600 Onboard Receiver Frsky version: Built-in SPI Frsky receiver with telemetry(D8/D16 switchable) Flysky version: Built-in SPI Flysky receiver with telemetry(

NameLessRC N47 105mm F4 2.5 Inch FPV Racing Drone PNP BNF w/ Caddx EOS2 Camera Specification: ( Manual) Brand Name: NameLessRC Model: N47 Item Name: 105mm F4 2-3S 2.5 Inch FPV Racing Drone Drone Wheelbase: 105mm Propeller: Gemfan 65mm (2.5 inch) Propeller Input Power: 2-3S Lipo battery Camera: Caddx EOS2 Antenna: Copper pipe antenna VTX: NameLessRC Nano400 VTX FC & ESC: NameLessRC AIO412 (2S-4S F4 12A) Motor: 1103 8000KV Optional Receiver: PNP ( Without Receiver) / Flysky RS2A Receiver/ Frsky ( Fullspeedrc frsky nano v2 RX)/ DSMX ( Fullspeedrc DSM Nano 2 RX Weight: 42g (NOT Included battery) Package Included: 1x N47 105mm FPV Racing Drone

DYS ELF 83mm Micro Brushless FPV Racing Drone BNF RTF Frsky Type D8 RX F3 10A BLheli_S Dshot 5.8G 25MW 48CH VTX Description: Brand: DYS Item name: ELF 83mm Micro Brushless FPV Racing Drone Wheelbase: 83mm Weight: 80g (battery included) Receiver: Frsky Type D8 Brushless Motor: BE1102 10000KV Brushless ESC: 4 in 1 Blheli_S Dshot F10A Flight Control: F3 Camera: 800TVL HD (horizontal resolution) 1.8mm 170 (no microphone) Video transmitter: 5.8G 40CH 25mW VTX distance: 300M Propeller: Micro 1.7 inch 5 blades prop Battery: 600mAh 2S 7.4V LiPo Flight Time: Around 6 minutes Remote Control: 2.4GHz wireless radio control, DYS new remote Remote Control Channel: 8 Channels Remote Control distance: 300M Features: Could be the smallest racing quad ever using BE1102 KV10000 brushless motors. Almost like a full-sized racing quad with F3 FC and 4 in 1 Esc squeezed into a 83mm tiny body with even ideal propeller protection. You can fly it safely indoors or outdoors avoiding high spare part cost. Use 1.7in 5 blade propeller which offers it great power. The receiver is Frsky Type that is compatible with most FRSKY radio. You can choose to use the radio coming with this quadcopter or use your own FRSKY radio like X9D or X12S. Comes everything you need even including a 800tvl camera and a 25mw 40CH 5.8G VTX that's compatible with most video receivers or FPV goggles on the market. Package included: BNF: 1 x DYS ELF 83mm Micro Brushless FPV Racing Drone 1 x F3 flight controller 1 x Frsky type recei

WolfBox 1000mW 433MHz Long Range UHF Transmitter TX 100mW Receiver RX Combo for X9D X12S 9XR Description: WOLFBOX LONG RANGE UHF TX Channel: Default 8CH, Max. 16CH(Users can customize) Frequency: 416-463MHz Transmission Power:1W Working Voltage: 6.5-28V Wide Voltage Input Input Signal: PPM Programme Method: bluetooth serial port, software programe Transmission Distance: Depends on the antenna Compatible with Frsky X9D,X12S,9XR,9XR PRO,Flysky 9,JR 9XII etc. JR Module WOLFBOX LONG RANGE UHFRX Channel: Default 1-8CH+RSSI, Max. 16CH(Users can customize) Frequency: 416-463MHz Transmission Power:100mW Working Voltage: 4-6.5V Configuration: Adjust parameter by wireless transmission Transmission Distance: Depends on the antenna Package Included: 1 x WOLFBOX 433 TX 1 x WOLFBOX 433 RX 2 x Antenna

FrSky G-RX6 16CH Telemetry Receiver PWM SBUS Outputs for RC Drone FPV Racing This FrSky G-RX6 is designed to be used with Gliders. FrSky built a variometer sensor right into the X6R receiver, this will give you telemetry data like altitude and vertical speed. The G-RX6 features 6 PWM outputs with higher precision and lower latency. The latency of the PWM output is 9ms less than that of the X6R, in high speed mode. It also supports the redundancy function, so it can be used in conjunction with other receivers. The G-RX6 and the whole RX-line has a 40% increased operating range compared to the previous X series receivers. Specification: Brand name: FrSky Item model: G-RX6 Number of Channels: 16CH (1-6CH PWM from conventional channel outputs, 1-16CH from SBUS OUT port) Operating Voltage Range: 3.5V-10V Operating Current: 100mA@5V Operating Range: >2km Servo Frame Rate: 9ms (HSHigh Speed Mode)/18ms (FSNormal Speed Mode) Dimension: 21.1137.3mm (LWH) Weight: 2.2g / 2.6g (with two antennas) Feature: High sensitivity (40% Increase of the range compared to previous X series receivers) Integrated with high precision variometer sensor Higher precision PWM Lower latency PWM output Lower power consumption Supports redundancy function Smart Port enabled and support telemetry data transmission Battery voltage detection 2 detachable IPEX connector antennas Package Included: 1 x G-RX6 Receiver

Jumper R8 16CH RC Receiver Compatible T16 FrSky D16 D8 Mode Support PIX PX4 APM Flight Controller PWM SBUS Output OVERVIEW: The R8 receiver is the first receiver that can directly transmit the PIX and PX4 flight control data (TX, RX) to the remote control of the world, and can display the flight control data to the remote control through the APM script. Since then, don't have to install additional converters for getting data back from PIX, PX4. Specifition: Item name: Jumper R8 Receiver Number of channels: 8ch (PWM) / 16ch (SBUS) RSSI (Signal Strength Indication) output: PWM Operating voltage range: 4.0~8.4V Operating current range: 100mA@5V Effective distance: full distance (>2.0km) Weight: 10g Compatibility: FrSky D8 D16 mode Features: - More channels: 1-8 channels from traditional channel output, 1-16 channels from SBUS port - RSSI output: analog voltage output (03.3V) - Two-way full duplex transmission (Telemetry) With RSSI output: analog voltage output (03.3V) Pair code method: 1. Press the bind button on the receiver, red/green LED solid on 2. On radio side, select Frsky D16 protocol (T12/T16: Multi Frsky D16); 3.When Red LED is flashing, binding succeeded. 4. After binding, withdraw the binding mode and power up the receiver again. Green Led turns solid on. LED color description. (The green light is always on: the signal is good; the green light is blinking: the signal is bad; the red light is always on: the signal is lost) Package Included: 1 x R8 Receiver

Happymodel Larva X 100mm Crazybee F4 PRO 2-3S 2.5 Inch FPV Racing Drone BNF w/ Runcam Nano2 Camera Notices: Because Emax can't provide Avan rush propellers in time, so will send it w/ HQPROP T2.5*2.5*3 propellers and EMAX Avan rush propellers randomly . Click here to buy spare parts togther. Specification: Brand Name: Happymodel Model: Larva X Item Name: 100mm 2-3S 2.5 Inch FPV Racing Drone Wheelbase: 100mm Size: 88x88x45mm (without propellers) Weight: 50g (without battery) Drone Version: BNF ( With Receiver & Without Battery) Happymodel EX1103 7000KV Motor Mode: EX1103 KV options: KV7000 Configu-ration:9N12P Stator Diamter:11mm Stator Length:3mm Shaft Diameter: 1.5mm Motor Dimension(Dia.*Len):13.5x16mm Weight:3.7g Crazybee F4 Pro V3 Flight Controller (Frsky version) CRAZYBEE F4FR PRO V3.0 Firmware target: CrazybeeF4FR (Flysky version) CRAZYBEE F4FS PRO V3.0 Firmware target: CrazybeeF4FS (No RX version) CRAZYBEE F4 PRO V3.0 Firmware target: CrazybeeF4DX MCU: STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU-6000 (SPI connection) Board Size: 28.5x 28.5mm Power Supply: 2-4S battery input (DC 7-17V) Built-in 10A (each) Blheli_S 4in1 ESC Dshot600 ready Frsky version Built-in SPI Frsky receiver with telemetry(D8/D16 switchable) Flysky version Built-in SPI Flysky receiver with telemetry(AFHDS/AFHDS2A switchable) No RX version need to add external Receiver Built-in Betaflight OSD(SPI Control) Built-in Current meter Max 70A Current meter scale set to 470 Built-in 5V 1A BEC Built-in volt