Turnigy

Flit10 RX 2.4G 10CH Micro Flysky Compatible Ibus Receiver with Telemetry for FS-i6 FS-I6X FS-i6S Turnigy Evolution Description: Item Name: Flit10 RX Channel: 10 2.4G Mode: The second generation of an enhanced version of the automatic FM digital system Antenna Length: 10mm * 2 (dual antenna) Input Power: 4.0-6.5V DC Weight: 3.1g Size: 25mm*15.5mm*5.5mm Color: Black Signal Output: IBUS Telemetry: Yes Remote Distance: 500m Support Betaflight / INAV IBUS Telemetry Best for FPV Racing drone Compatible with FS-i4, FS-i6,FS-I6X,FS-i6S, FS-i10,FS-iT4S, Eachine I6,Turnigy I6S, Turnigy Evolution Telemetry Configuration: Package Included: 1 x Flit10 RX 1 x IBUS Telemetry module 2 x cables

1.7g Fli14+14CH Receiver Compatible Flysky AFHDS-2A w/ RSSI Output for FS-i6 FS-i10 Turnigy I6S Radio Transmitter Specification: Model: Fli14+ Item Name: 2.4G 14CH Compatible Flysky AFHDS-2A Receiver Channel: 14CH Protocol: AFHDS-2A 2.4G Mode: The second generation of an enhanced version of the automatic FM digital system Antenna Length: 70mm (Dual Antennas) Input Voltage: 4-6.5V DC Weight: Only 1.7g Size: 25x15x5mm Color: Black Signal Outpu: IBUS RSSI Output: Channel14 No ground interference ( Transmitting and receiving 1 m from the ground): more than 500m Features: - Customized for Betaflight - RSSI Display Via OSD without any hack compatible with all Flysky AFHDS-2A protocol transmitter - Telemetry Output: RSSI & RX Battery - Support RSSI Via Channel14 (Aux10 in Betaflight) - Compatible with FS-i4, FS-i6, FS-I6X, FS-i6S, FS-i10, FS-iT4S, Eachine I6,Turnigy I6S,Turnigy Evolution - Best for Racing Drone Binding procedure: 1. Power for the Fli14+ Receiver while press and holding the bind button 2. The LED will blinking fast which indicates the receiver is in binding mode 3. Get the Flysky transmitter into binding mode and the LED on the receiver will getting to be solid and this indicates binding successfully Package Included: 1x Fli14+ Receiver

FrSky DJT-JR 2.4GHz Transmitter Telemetry Module The DJT telemetry transmitter module is a great choice if your transmiter is compatable with the JR modules. (as well as Turnigy 9x/FlySky 9x/EMAX 9x) The Telemetry Radio System developed by FrSky provides an additional return link that is used for monitoring the Rx's voltage, poor receiver reception, temperature, location, speed and so on. The module is compatible with both the V8-series (non-telemetry) and the D-Series (telemetry) receivers. Description: Operating voltage range: 6.0V-13.0V Operating current: 50mA Output power: 60mW Resolution: 11bit (3072) Features: Advanced continuous channel shifting technology (ACCST SYSTEM) achieves highly reliable link in interference rich environments. Easy to bind and instant link-up Excellent reboot times All channels failsafe Quick response Very smooth servo movement Alarm on events of receiver (low battery voltages, poor reception, etc.) Error-free link, by using 48bits CRC algorithm Low power consumption Firmware upgradable Compatibility: V8 series: (Non-telemetry receivers) V8FR-HV, V8R7-HV, V8R7-SP, V8R4 D Series: (Telemetry receivers) D8R, D8R-II, D8RSP, D6FR, D4FR Compatible with the following transmitters: JR: 347, 388, 783, U8, PCM10, PCM10S, PCM10SX, PCM10IIS, 8103, J9303, MX-22, MX-24S, PX, 9XII Turnigy 9x/FlySky 9x/EMAX 9x Package included: 1 x DJT-JR Transmitter Module

Features:
Specially designed for Frsky transmitter, Incorporate CC2500 NRF24L01 A7105 CYRF6936 RF module in one single PCB board, supports more than 10 different protocols, such as Frsky, Flysky, WLtoys V2x2, Hubsan, Hisky and so on.
Control basically all of you toy-grade quad (Syma X1 X5C X8C X11 CX-10, H8C, Hubsan H107C H107D JXD 395 JJR/C 1000 X1 H21 H22 MJX X600 WLtoys V966 V262 V666 V676, to name a few) with one transmitter.
For this 4 in 1 module to work, soldering is required, if you're not comfortable with soldering, please practice first or have someone else to do it for you.
High quality and durable in use.
Features PA(Power Amplifier) and LNA(Low Noise Amplifier) for best performance.

Description: This adapter works with all Fatshark FPV video glasses or any other FPV headset provided they are equipped with the same 5.5 - 2.1mm dc plug and the polarity is +ve in the middle and -ve on the outside, including but not limited to: Fatshark, Skyzone and Boscam. If you are unsure of your current polarity please check it with a multimeter on the original battery that came with your equipment. It will save you a good amount of money just because you can use any battery or power supply with an XT60 connector as long as it is within Fatshark's allowed voltage. Specifications: Brand Name: URUAV Item Name: T Plug to DC5.5X2.1 Adapter Weight: 4g Features: - Designed to work with any FPV goggles fitted with a 2.1-5.5mm DC plug. - Polarity is ve+ in the interior, ve- on the outside. - 4 grams weight, minimal efficient design. - Angled to reduce cabling and improve performance. - Black mat Turnigy heat shrink for pleasant appearance. - Use any battery or power supply that has an T connector. Note: Do not change batteries or power supplies with the adapter plugged in the goggles as this will decrease the adapters life. Package Included: 1x URUAV T Plug to DC5.5X2.1 Lipo Battery Adapter

FS82 MICRO 2.4G 8CH Flysky Compatible Receiver With PPM I-Bus Output Specification: Item Name: FS82 Micro 2.4G receiver Channels: PPM 8CH / IBUS 10CH Frequency range: 2.4082.475GHZ 2.4GHz system: AFHDS 2A Work Mode: IBUS or PPM IBUS connector: 1.0 SH 3pin plug PPM connector: Solder pad Failsafe function: Support(Only IBUS Mode) Transfer method: FHSS Antenna length: 30mm No ground interference ( Transmitting and receiving 1 m from the ground): >300m Working current: 40mA Size: 20*13*4.5mm Weight: 1.2g Compatible Transmitter: Compatible with FSi4, FSi6, FSi6S, FSi6X, FSi10, FSGT2E, FSGT2G, FSGT2F,Turnigy Evolution Binding Procedure: Connect the battery to the receiver while holding the binding button on the board ,the Blue LED will blinking fast, this indicates the Receiver is in binding mode. Then release the binding button. Turn on your radio and Set receiver mode to AFHDS 2A, then get your radio into binding mode. The blue LED on the Receiver will turning off for a second and then starting to blinking slowly, this indicates binding successfully. Package Included: 1x receiver

Description: Battery parameter:ZOP Power 11.1V 2200MAH 8C Capacity:2200mAh Size:21*20*100MM Weight:90g Continuous Discharge Rate:8C Colors:Standard Colors For Devo F7 Devo7 Devo10 Turnigy 9XR and JR transmitter 2200mAh 11.1V 8C Li-Po Battery for DEVO 10 / DEVO 7 / JR / FUTABA Transmitter Li-poly RC Battery Note: due to the difference between the measurement, the battery dimension and weight may have little error. Horizon: DSX7,DSX8 WFLY: 8CH and 9CH transmitter JR: 9XII,DX7,DX9 FUTABA: FF9 10C T8FG and so on Walkera: DEVO 10/ DEVO 7 RadioLink AT9 AT10 And so on Caution: Don't over-charge, or over-discharge batteries. Don't put it beside the high temperature condition. Don't throw it into fire. Don't throw it into water. Package Included: 1 x ZOP Power 11.1V 2200MAH 8C Lipo Battery

Beecore Lite Silverware Brushed Flight Controller Built in Bayang Protocol for Tiny Whoop Blade Inductrix E011 Jumper T8SG MTX9D MTXI6 Module Specifications: Item Name: Beecore Lite Silverware Brushed Flight Controller CPU: STM32F030 Six-Axis: MPU6050 ESC: All FETs are rated at 12A maximum. Support 6x15mm/7x20mm/8x20mm/8.5x20mm etc motors. Size: 26mm x 26mm, fully compatible with the Inductrix quad frame and mounting pattern Firmware : Silverware (BoldClash-BWHOOP-B-03) Receiver Module: XN297LBW Receiver Protocol: Bayang protocol Power Cable: 50mm, with JST-PH 2.0 connector Weight: 2.7g Features: - Support level mode and acro mode. Also it has the ability to change settings for custom builds, or to adapt to personal preferences by stick gestures. - Designed to work with current Tiny Whoop or Blade Inductrix frames - Built in Bayang protocol native receiver, compatible with almost radio transmitter with deviation firmware or deviation compatible transmitter module - The flight controller board comes pre-flashed with Silverware firmware, and pre-soldered 55mm power cable pigtail with JST-PH 2.0 connector, AKA PowerWhoop connector. Compatible Radio Transmitter: BETAFPV TX01 radio transmitter Radio transmitter of toy drone like JJRC H67, Eachine E011 etc, that using the Bayang protocol Jumper T8SG radio transmitter MTX9D multiprotocol module (Suit for Frsky Tanaris QX7 X9D X9D Plus X12S, Flysky TH9X, Turnigy 9XR/9XR PRO) MTXI6 multiprotocol module(Suit for Flysky i6, i6S, I6X, I1

iRangeX IRX4 2.4G CC2500 NRF24L01 A7105 CYRF6936 4 IN 1 Multiprotocol STM32 TX Module With Case Description: The 4 in 1 wireless module integrate four RF chips (CC2500,NRF24L01,A7105,CYRF6936) into one single circuit board,with MCU baseplate,can support a variety of remote control protocols by identifying the PPM signal output of the remote control,such as Walkera DEVO,Spektrum DSM2,Flysky,Frsky,WLToys,Hubsan,Hisky,etc. It can control up to several hundreds airplanes (or receivers). This module can recognize the remote control PPM signal, then converted into the corresponding standard wireless remote control format,which means that in theory as long as the remote control is with analog functions, it can work. This Multiprotocol TX Module is the STM32 board, all protocols are included. It is suitable for many brand's quadcopters,helicopters and airplanes .You can control RC quadcopters,RC helicopters or RC airplanes flexibility when you insert the TX Module to your Frsky X9D/X9D Plus/X12S,flysky TH9X,Turnigy 9XR/9XR PRO transmitter. As long as your transmitter can use the Open TX firmware,it is compatible with this module. You will get many new ways to control the RC models. Specification: Brand Name: iRangeX Item Name: IRX4 Band: 2.4G Weight: About 40g Firmware: STM32 Dimension: About 49x22x65mm Antenna Length: About 108mm Compatible Transmitter: Frsky: All the frsky transmitter Futaba: Futaba S-FHSS transmitter Flysky: TH9X (Note: The plastic base of the pins on the transmit

Specification: Item name: Battery Adapter Weight: 4.54 g Features: Designed to work with any FPV goggles fitted with a 2.1-5.5mm dc plug Polarity is ve+ in the interior, ve- on the outside 5 grams weight, minimal efficient design Angled to reduce cabling and improve performance Black mat Turnigy heat shrink for pleasant appearance Use any battery or power supply that has an XT60 connector. This adapter uses an XT60 to plug in the power supply and a dc 2.1mm male to plug in the goggles. It will work with all Fatshark FPV video glasses or any other FPV headset provided they are equipped with the same 5.5 - 2.1mm dc plug and the polarity is +ve in the middle and -ve on the outside. This adapter will save you a good amount of money just because you can use any battery or power supply with an XT60 connector as long as it is within Fatshark's allowed voltage. When connecting and disconnecting the battery please remove the adapter from the FPV glasses first and hold on the XT60 male while pulling or pushing the XT60 female power supply connector. Please do not change batteries or power supplies with the adapter plugged in the goggles as this will decrease the adapters life. This adapter works with all original Fatshark goggles and the polarity is positive in the middle negative on the outside. It is also suitable for any other FPV goggles fitted with an 2.1-5.5mm dc power plug including but not limited to: Fatshark, Skyzone and Boscam. If you are unsure of your current polarity ple