Fc Osd

Features:Small size: 36 * 36mm, light wight: about 8gSupport SBUS/PPM AND Spketrum DSMX PortsBuilt-in Betaflight OSD, BEC, video filter and current sensorSupport Smart audio V2, tune your PID's and configure the omnibus FC from transmitterClassic design, using F4 MCU controls OSD over SPI bus, newly upgrade BMP280 as barometerSD card reader to record flight data, easy to apply blackbox function. (SD card not included)

Features:Built-in BETAFLIGHT OSD to adjust PID, BEC, BarometerSupport PPM, SBUS, IBUS, DSM2 / DSMX Receiver (UART1)Support SAMRT AUDIO, adjust the VTX by OSD (UART3)MicroSD card blackbox, large capacity storage, Dshot support40 Channels transmitting power: 25/200/600/800mW switchable

Integrated FC & ESC, the lightest amount 4.58g Official Spracing-F3 ,latest BF firmware No Soldering,Easy Installation Silica gel shock absorption pads help filtering MPU noise,makes your flight more stable. Esc each port send continuous 2A, Max 3A output; Whoop Size is easy to install

SKYSTARS TurboS F405 Betaflight Flight Controller OSD 9V/2A BEC 2-6S 30.5x30.5mm for RC Drone Specification: Skystars TurboS F405 FC Item name: F405 Betaflight Flight Controller Input power: 7.4-25V (2-6S) BEC: 9V/2A MCU: STM32F405 Gyro: MPU6000 Flash: 16MB OSD: AT7456 Mounting hole: 30.5*30.5mm Weight: 6.8g FC Features - Supports Betaflight and Cleanflight. - Additional UART (UART 4) - Additional UART (UART 5) - Incould socked head and flat pads for more secure soldering especially for beginners. - I2C pad available for certain external sensors. Package Included: 1 x F405 Betaflight Flight Controller

MAMBA F722 MINI 2-6S 5V 2A BEC OSD Flight Controller 20x20mm for RC Drone FPV Racing Specification: Item name: MAMBA F722 MINI Betaflight Flight Controller MCU: 216MHz STM32F722RET6 32BIT IMU: MPU6000 Baro: No OSD: BF OSD Blacbox: 16M Flash Memory Uarts: 6Set ESC Soft: Dshot300/600/1200 ESC Telemetry: RX2 LED: Blue&Orange for FC Status,,White 5V,Red 3.3V Mounting: 2020mm,2 Dimensions: 3036.513.5mm Weight: 11g WS2812 LED Control: BF LED Control Smartaudio: Yes RSSI: Yes Buzz: Yes PDB Specifications Input: 2~6S Lipo (8.4~25V) VTS Protection: Yes BEC: 5V 2A (Max 3A) FC Firmware BetaFlight Target: MAMBA F722 Package Included: 1 FC MAMBA F722MINI 4 Silicon grommets M4.3 to M3 1 Panaso nic Low ESR 35V/470uF 1 AMASS XT60 2 Wire 20 Silica gel O ring

Racerstar StarF4_6S F4 OSD Flight Controller AIO BEC Current Sensor Built-in 40A BL_S 2-6S 4in1 ESC Specification: Brand Name: Racerstar Model: StarF4_6S Item Name: F4 OSD Flight Controller AIO BEC Current Sensor & 40A BL_S 4in1 ESC Size(PCB): 36x36mm Weight: 17g F4 OSD FC + BEC + Current Sensor + Blackbox Input Voltage: 2-6S Lipo SBEC Output: 5V@3A MCU: STM32F405MCU Gyroscope: ICM-MPU6000 Blackbox: 16MB 40A BLheli_S 4in1 ESC Con. Current: 40A Burst Current: 45A (10S) Lipo Battery: 2-6S Programming: YES Features: - F4 Flight Controller Board integrated with ESC Module - BB2, 48MHZ Chip - BLheli_S Firmware, - 4 in 1 ESC, Super small size (36*36mm) and light weight, easy to install and use - With 5V 3A BEC Output - With Current Sensor - Support 2-6S Lipo Battery - Support Oneshot42, Oneshot125, Multishot and 16.5 Dshot600 Package Included: 1x StarF4_6S F4 FC Built-in 40A ESC 2x Cable 1x bag of screws 1x Capacitor 1x Manual

MXK F722 Brushed Quadcopter Frame Kit Built-in Bluetooth OSD Description: MCU: 216MHz STM32F722 IMU: MPU6000 accelerometer/gyro Baro: BMP280 OSD: AT7456E Blackbox: W25Q128FVSIG(16M) BLE Module: Inner connect to UART5(MSP & Baud 9600) for remote setting with SpeedyBee App or other similar apps 4x Uarts (1,2,3,5) 4 x 9.5A Mosfets 2x LEDs for FC STATUS (Blue) and 3.3V indicator(Red) UART2-RX(PPM,SBUS) LED_Strip : Yes Battery Voltage Sensor: 1:10 (Scale 1100) Beeper : Yes RSSI: Yes Input voltage range: 1~2S LiPo 3.3V(3V3) 0.3A BEC(Designed for Spektrum RX) 5V(5V) 1A BEC(Designed for Flight controller, Receiver, OSD, Camera,Video Transmitter,Buzzer, LED_Strip etc) FC Firmware betaflight Physical Dimensions: 102X86mm Weight: 9g Package Included: 1x MXK F722 Brushed Quadcopter Frame

Description: Brand: Aikon Item Name: F7 Mini V2 MCU: STM32F722 IMU: MPU6000 Motor outputs: 4-6 IMU Interrupt: Yes VTX switch: Yes BARO: Optionally DJI AIR unit port: yes VCP: Yes Hardware UARTS: 5 OSD: Yes Blackbox: SPI 16MB PPM/LED_STRIP Shared: Yes Battery Voltage Sensor: Yes Integrated Voltage Regulator: Yes Buttons: Boot Package Included: 1* Aikon F7 Mini V2

Racerstar StarF4S 30A Blheli_S Dshot 4 in 1 ESC AIO F4 OSD Flight Controller w/ BEC Current Sensor Note: The 4 installing holes were linked to the possitive of power. ( battery +) Therefore, must use the plastic screws or any others non-conductive screws to install. If not, the FC/ESC/Receivers will be brunt. Specification: ( Manual) Brand Name: Racerstar Model: StarF4S Item Name: 30A Blheli_S 4 in 1 ESC AIO F4 OSD Flight Controller with BEC and Current Sensor Lipo Battery: 2-4S Con. Current: 30A Peak Current: 35A (10S) LBEC: 5V @3A Programming: YES F4 FC + OSD + BEC + Current Sensor Input Voltage: 2-4S Lipo Output Voltage: 5V@1A Sensor: STM32F4 CPU ICM-MPU6000 Accelerometers and Gyroscopes SPI MicroUSB socket Size(PCB): 36x36mm Weight: 22g Features: - Built-in F4 Flight Control Board integrated with OSD - BB2, 48MHZ Chip - Blheli_S Firmware, - 4 in 1 ESC, Super small size (36*36mm) and light weight, easy to install and use - With 5V 3A LBEC - With Current Sensor -Support 2-4S Lipo Battery - Support Oneshot42, Oneshot125, Multishot and 16.5 Dshot600 - All codes use damped light mode.Damped light does regenerative braking, causing very fast motor retardation, and inherently also does active freewheeling. Package Included: 1x Racerstar 30A 4 in 1 ESC Buit-in F4 OSD FC 2x Cable 1x bag of screws 1x Manual

Features: All new Omnibus F4, based on the design of the popular omnibus F3.SD card reader to record flight data, easy to apply black box function. (SD card not included)Built with BEC, no extra BEC needed.STM32 F405 MCU, Runs Betaflight 3.0.1 firmware, could run faster loop time. Using F4 MCU controls OSD over SPI bus in DMA mode. OSD Configuration has been included in Betaflight GUI. SBUS/PPM input (Pinheaders).6PWM output (1-4Pinheaders and Sh1.0 Plug, 5-6 as Pinheaders).SPI Sensor MPU6000.Included 128Mbit Flash, please always use BEC for the FC. Supported by BETAFLIGHT and dRonin.

Original Airbot Omnibus F4 Pro V3 Flight controller SD 5V 3A BEC OSD Current Sensor LC Filter Specification: Brand name: Airbot Item name: Omnibus F4 Pro V3 Flight controller SPI Gyro MPU6000 On-Board OSD (controllered by Betaflight, FC over SPI bus) MicroSD Blackbox Baro (BMP280) F4 Processor (F405) 5v3a SBEC Built-in Current Sensor On-Board Video Filter (only can supply 5V to VTX and Camera) Package Included: 1 x Omnibus F4 Pro V3 Flight controller

Description: iFlight the Force 5.8G 48CH 0/25/100/200/400/600mW Switchable FPV Transmitter, support OSD Frequency and Power tuning. The output power is stable, the far transmission distance: 0.5km@25mW, 1km@200mW, 2km@600mW. Specifications: Brand Name: iFlight Item Name: the Force Input Voltage: 7-24V DC Channel: 48 Power Transmission: 0mW / 25mW / 200mW / 400mW /600mW Size (mm): 36*36mm Weight: 4.3g(Does not contain antenna) Connector Type: MMCX Connector Protocol: IRC Tramp Features: - Support OSD Frequency and Power tuning; - The output power is stable, the far transmission distance: 0.5km@25mW, 1km@200mW, 2km@600mW; - Transmit power 6 gear switch: 0mW/25mW/100mW/200mW/400mW/600mW; - Output 48 frequency points, and has E group 8 race frequency at the same time using each other without interference; - Frequency lock fast, the boot does not interfere with companions; - Built-in output power self-check function; - Full format video format: NTSC /PAL; - Wide input voltage range. low power consumption; 7V~24V, +12V/260mA@600mW; - Small volume: 36mm36mm5mm; mounting holes correspond exactly CC3D NAZE32 F3 F4 Flying control - Lightweight: 4.3g(Does not contain antenna) Smart Audio - OSD Frequency and Power Tuning: Power the Force VTX by 7-24V, Connect the RX port on VTX to FC. Let's take iFlight REVO Bee F4 as an example, RX port on VTX connect to RX port on FC, Video IN on VTX connect to Video Out on FC. Bind Radio control to the receiver, receiver connect to FC finish setting

Wing FC-10 DOF Flight Controller INAV OSD Accelerometer Barometer Gyro Compass For RC Drone STM32F405 MCU, the refresh rate is up to 168MHz, integrated MPU9250 nine axis sensors (three axis gyroscope + three axis accelerometer + three axis electronic compass) and barometer, built-in electronic compass (Compass) only need external GPS, can achieve fixed point fixed height, one key return and equal work energy, with very fast reaction, more suitable for high-speed competition. Aerobatic flight. Features Support INAV tuning to support OSD data return. It has the function of partition board, and supports two simultaneous electrically adjustable output. There are 4 PMW steering gear output to meet various fixed wing models. It can connect to GPS and realize the function of positioning and returning. (GPS purchased separately). Reserved BB ring interface, easy to achieve unlock, lock, search star, search and other prompts. The built-in 5V/3A BEC output is convenient for power supply for all kinds of equipment. Specification Mounting:30.5 x 30.5mm,4mm with Grommets 3mm Dimensions:54 x 36 x 13 mm Weight:10g MCU:168MHz STM32F405 IMU:MPU-9250 accelerometer/gyro/Compass (SPI) Baro:BMP280 (I2C) OSD:INAV OSD w/ AT7456E chip Blackbox:NO VCP & 6x UARTs 2x Motors,4x Servos outputs Built in inverter for RC input (UART3-RX) TBS Receiver:UART5-RX Beeper:Yes Default firmware : inav_1.9.0_FF_F35_LIGHTNING.HEX Reference software : inav-configurator Packing Included 1 x Wing Fc-10 DOF FC 4 x M3 Du

Hobbywing XRotor Micro OMNIBUS F4 G2 Flight Controller OSD STM32F405 for RC Drone FPV Racing Specification: Brand name: XRotor Item name: F4 G2 Flight Controller Firmware: OMNIBUSF4SD FC Programming: Supported Programming via: Betaflight/Cleanflight-configurator or Others Compatible with (Modes): PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600, DShot1200, Proshot1000 and etc. Compatible with (Transmitters): PPM, Spektrum, SBUS, SUMD, SUMH, XBUS, IBUS, JETIEXBUS, CRSF, SRXL, and etc. OSD: Built-in Voltage Monitoring: Supported Current Monitoring: Supported External Buzzer: Supported LED Control: Supported BEC: No USB Port: MicroUSB Size: 36*36mm Weight: 6g User Manual, Download Package Included: 1 x F4 G2 Flight Controller

LDARC Kingkong KK 5GT 213mm F4 OSD FPV Racing Drone w/ BL_S 48CH 25/200/600mW VTX Runcam Swift Mini Specification: Brand Name: LDARC Model: KK 5GT Item Name: 213mm F4 OSD FPV Racing Drone Version: PNP ( Without Receiver and Battery) Wheelbase: 213mm Material: Carbon Fiber & 7075 Aluminum Alloy Input Voltage: 3-4S Recommend Battery: 4S 1300-1800mAh above 25C Lipo Weight: 336.7g (Without Receiver and Battery) 213mm Frame Kit Wheelbase: 213mm Material: Carbon Fiber & 7075 Aluminum Alloy Arm Thickness: 5mm Weight: 102.5g KK Super Flytower FC AIO VTX Tower Monting Hole: 30.5x30.5mm Tower Height: 16.5mm ( Include heat sink ) Tower Weight: 28.9g F4 Flight Controller Integrated with VTX Module: Chip: STM32f405 MCU Gyroscope: MPU6000 Firmware: OMNIBUSF4SD OSD: Betaflight OSD With 5V @ 3A ( VTX and FC have been used. Suggest less than 6 LED ) ( If use more than 6 LED, please use BEC Module ) Support PPM Recceiver/SBUS/DSMX Receiver ( PPM Receiver need solder the pad) Channel: 48CH Power: Off/25/200/600mW ( TX control through the FuriousFPV /Tramp peropheral protocol ) Camera Voltage: 5V Weight: 11.3g Size: 36x36mm ( 30.5x30.5mm Mounting Hole) KK Super Flytower 40A BLheli_S 4 in 1 ESC Working Voltage: 2-4S Lipo Con. Current: 40A Burst Current: 45A (5S) Firmware: BLheli_S/Dshot150/DShot300/DShot600 16.6 (G_H_30) Size:39x41mm ( with pad ) Moutning Hole: 30.5x30.5mm Weight: 12.5g Support BLHeliSuite setting -Integrated PDB, -Integrated Battery Monitoring - Integrated FC Power XT2306 2500KV

FX3 is similar to the FX2 but has a smaller profile that uses 20x20mm mounting pattern, in the cost of lower max output power, to be designed for smaller micro builds. Specification: Input voltage: 7-24V Extra feature: Smart Audio/PIT Mode Power supply: 5v camera@under 0.3A max Output power: 25mW:100mA/200mW:200mA/400mW:250mA/600mW:320mA@12v Range: Up to 2km with omnidirectional RHCP antenna Antenna connector: MMCX Port connector: JST,6pin Dimensions: 26(W)x26(D)mm,20x20mm(hole) Weight: 4.6g(excluding antenna) Features: Support Pit Mode 25mW/200mW/400mW/600mW switchable One button frequency and power setup OSD conguration using smart audio 7-24v input with 5v output Package included: 1 x AKK FX3 5.8Ghz 37CH 25/200/400/600mW Switchable FPV Transmitter VTX with MMCX Integrated OSD FC 1 x Cable 1 x MMCX pigtail

T-motor F4 OSD Flight Controller & F55A PRO II BL_32 DShot1200 4in1 ESC Stack for RC Drone FPV Racing Specification: Brand Name: T-motor Item Name: 30.5x30.5mm F4 FC & 55A BLheli_32 4in1 ESC Stack T-motor F4 OSD Flight Controller Input Voltage: 2-8S ( 8.4V-33.6V) Firmware: TMOTOR F4 (Betaflight) OSD: Betaflight OSD BEC: 5V @ 2A MCU: STM32F405RGT6 Gyro: ICM20602 Flash: Onboard 16M Size: 37x37x7mm Mounting Hole: 30.5x30.5mm Weight: 7g F55A PRO II BLheli_32 4in1 ESC ( Manual) Continous current: 4*55A Burst current: 4*75A Input Voltage: 3-6S Lipo BEC Output: [email protected] Size: 45x41x7.3mm Mounting Hole: 30.5x30.5mm Weight: 17.5g (including heatsink) Package Included: 1x T-motor F4 Flight Controller 1x F55A PRO II ESC 4x Cable 3x Cable Connectors 1x bag of Anti-vibration Damping Balls 1x XT60 Connector Cable 1x Capacitor

HAKRC BF3.2 Omnibus F4 Flight Controller 2-4S Integrated Betaflight OSD PDB Current Meter Description: Brand name: HAKRC Item name: BF3.2 Omnibus F4 Flight Controller Working voltage: 2-4S Lipo Firmware: BetaFlight 3.20 SD (PPM and LED alternative, or flash BetaFlight 3.17 SD to use PPM LED at the same time.) PDB: copper thickness: 3 OZ, max continuous working current: 150A OSD: Betaflight OSD BEC: 5V/2A Camera and VTX voltage: 5V Black box: TF cassette, max support 32G Receiver: support PPM, SBUS, IBUS, DSM2 SBUS: RX1 IBUS DSM2: RX6 Mounting hole: 30.5x30.5mm Size: 44*36mm Weight: 9g Features: Integrated PDB, Betaflight OSD, barometer, voltmeter and current meter. Support BlheliSuite programing. Support CF, INAV flash firmware. Support OneShot DShot. Support LED_Strip and BB alarm. Package included: 1 x BF3.2 Omnibus F4 Flight Controller